|
Post by Captain Awesome on Nov 10, 2022 17:15:52 GMT -8
Nice!
|
|
|
Post by 69Rebel on Nov 11, 2022 8:20:51 GMT -8
I am kinda wishing I had gotten the Advance Adaptors bell rather than the Quicktime unit. It hangs down pretty low, barely above the oil pan, and has no inspection cover.
|
|
|
Post by 69Rebel on Nov 12, 2022 17:21:43 GMT -8
I think I have the cross member sorted out, though I might have been wrong about not needing to cut the tunnel. I'll take some pics when I know more.
|
|
|
Post by 69Rebel on Nov 16, 2022 15:10:40 GMT -8
Anybody have a pic of where the pedal rod goes through the firewall?
|
|
|
Post by spud on Nov 16, 2022 15:40:47 GMT -8
I dunno what a rebel firewall may have, but javelins have a round knock out thats a little bigger than a quarter. The rod runs down from the pedal at about a 45 degree angle to the bellcrank.
|
|
|
Post by 69Rebel on Nov 16, 2022 16:10:01 GMT -8
There's a knockout under, and slightly toward the passenger side, of the steering column. About an inch or so in diameter.
|
|
|
Post by landbarge on Nov 16, 2022 16:34:35 GMT -8
Might be a little easier to see from below
|
|
|
Post by 69Rebel on Nov 16, 2022 16:49:43 GMT -8
I crawled under and looked. The only knockout I'm seeing would have the pedal rod crossing the brake rod near as I can tell, which is part of what has me questioning. As of yet, I have no clutch linkage.
|
|
|
Post by landbarge on Nov 16, 2022 17:48:53 GMT -8
I couldn't get a picture is with the nose of the car up to the wall. Should be between the column and frame rail.SShould be 2 dimples by the knockout for the boot attachment screws.
|
|
acm
Cool Froods
Posts: 310
Member is Online
|
Post by acm on Nov 17, 2022 16:40:20 GMT -8
On my 67 there's a reinforced piece of sheet metal for the master cylinder and there's a knockout at the bottom right of that panel. Like others mentioned, there's roughly an 2" knockout and 1 small screw dimple @ 6 & 12 o'clock.
The knock out is in the same location as the 69 AMX sitting next to the Rebel but the firewall is different.
I'm planning on running a hydraulic set up and a TKO600 on my Rebel and have the engine compartment ready for painting... I'd get you a few pics of the knockouts but I tripped today and used my phone as a landing device. Needless to say, cheap Samsung phone is rated for 250lbs falling on it it. Who knew.
Hopefully I'll have a new one soon and will post pics.
|
|
acm
Cool Froods
Posts: 310
Member is Online
|
Post by acm on Nov 17, 2022 17:34:26 GMT -8
Here's a pic I found on the computer. The green arrow points to the clutch punch out.
The red circle shows another punch out. It's easier to see/get too but the wrong one.
|
|
|
Post by 69Rebel on Nov 17, 2022 21:08:29 GMT -8
So it is under and a little towards the passenger side of the brake rod?
|
|
acm
Cool Froods
Posts: 310
Member is Online
|
Post by acm on Nov 18, 2022 6:28:39 GMT -8
Yes
|
|
|
Post by 69Rebel on Nov 18, 2022 6:30:06 GMT -8
Awesome. Thanks.
|
|
|
Post by spud on Nov 18, 2022 11:09:07 GMT -8
Dont punch out nuthin. Get the linkage and pedals and the little stuff will fall in place. Your getting there 😎
|
|